BIXOLON SRP-330 Manuale Utente

User’s Manual SRP-330 Thermal Printer Rev. 1.03 http://www.bixolon.com

Rev. 1.03 - 10 - SRP-330 Pin Number Signal Name Signal Direction Function 2 TXD Output Transmit data 3 RXD Input Receive data 4 DTR Output This

Rev. 1.03 - 11 - SRP-330 Pin Number Signal Name Signal Direction Function 2 DTR Output This signal indicates whether the host computer can receiv

Rev. 1.03 - 12 - SRP-330 1-2-2 Parallel Cable (IEEE1284) Pin No. Source Compatibility Mode Nibble Mode 1 Host nStrobe HostClk 2 Host / Printer D

Rev. 1.03 - 13 - SRP-330 1-2-3 USB Cable Pin No. Signal Name Assignment (Color) Function Shell Shield Drain Wire Frame Ground 1 VBUS Red Host Powe

Rev. 1.03 - 14 - SRP-330 1-3 Drawer Cable Connect the cash drawer cable to the cash drawer connector in the back of the printer. ※ Warning Use the

Rev. 1.03 - 15 - SRP-330 1-4 Setting the Dip Switches 1-4-1 Serial Interface • DIP Switch 1 SW Function ON OFF Default 1-1 Auto Cutter Selection Dis

Rev. 1.03 - 16 - SRP-330 1-5 Installing or Replacing the Paper Roll ※ NOTE Be sure to use paper rolls that meet the specifications. Do not use paper

Rev. 1.03 - 17 - SRP-330 1-5-5 Be sure to note the correct direction that the paper comes off the roll. 1-5-6 Pull out a small amount of paper, as

Rev. 1.03 - 18 - SRP-330 1-6 Using the Printer 1-6-1 Control Panel 1-6-2 Mounting 2” Partition Hang the partition at the front and press down

Rev. 1.03 - 19 - SRP-330 1-7 Connecting the computer You need an appropriate interface cable. 1-7-1 Plug the cable connector securely into the prin

Rev. 1.03 - 2 - SRP-330 Safety Precautions In using the present appliance, please keep the following safety regulations in order to p

Rev. 1.03 - 20 - SRP-330 1-8 Connecting the Power Supply ※ CAUTIONS When connecting or disconnecting the power supply from the printer, make

Rev. 1.03 - 21 - SRP-330 2. Self Test The self-test checks whether the printer has any problems. If the printer does not function properly, contact

Rev. 1.03 - 22 - SRP-330 3. Hexadecimal Dumping This feature allows experienced users to see exactly what data is coming to the printer. This can be

Rev. 1.03 - 23 - SRP-330 4. Specification Printing method Thermal line printing Dot density 180 dpi (7dots/mm) Printing width 72 mm Paper width 79.5

Rev. 1.03 - 24 - SRP-330 5. Appendix 5-1 Cleaning Printer Paper dust inside the printer may lower the print quality. In this case clean the p

Rev. 1.03 - 3 - SRP-330 CAUTION Violating following instructions can cause slight wound or damage the appliance. Do not use the printe

Rev. 1.03 - 4 - SRP-330 Warning - U.S.A This equipment has been tested and found to comply with the limits for a Class A digital device

Rev. 1.03 - 5 - SRP-330 Introduction The SRP-330 Roll Printer is designed for use with electronic instruments such as system ECR, POS, banking equ

Rev. 1.03 - 6 - SRP-330 Table of Contents 1. Setting Up the Printer ...

Rev. 1.03 - 7 - SRP-330 1. Setting Up the Printer 1-1 Unpacking Your printer box should include these items. If any items are damaged or missing, p

Rev. 1.03 - 8 - SRP-330 1-2 Connecting the Cables Connect the cable that is suitable for the specifications of the printer and the host computer (PO

Rev. 1.03 - 9 - SRP-330 Pin No. Signal Name Signal Direction Function BODY Frame GND - Frame Ground 2 TXD Output Transmit Data 3 RXD Input Receive D