BIXOLON SRP-350II Manuale Utente

User’s Manual SRP-350II Thermal Printer Rev. 1.04 http://www.bixolon.com

Rev. 1.04 - 10 - SRP-350II 1-2-3 USB Interface Pin No. Signal Name Assignment (Color) Function Shell Shield Drain Wire Frame Ground 1 VBUS Red Hos

Rev. 1.04 - 11 - SRP-350II 1-4 Setting the Dip Switches 1-4-1 Serial Interface • DIP Switch 1 SW Function ON OFF Default 1-1 Auto Line Feed Enable D

Rev. 1.04 - 12 - SRP-350II • Table 1 – Baud rate (bps) Selection Transmission Speed 1-6 1-7 1-8 Default 2400 ON OFF OFF 9600 4800 ON OFF ON 9600 OFF

Rev. 1.04 - 13 - SRP-350II 1-5 Installing or Replacing the Paper Roll ※ NOTE Be sure to use paper rolls that meet the specifications. Do not use pa

Rev. 1.04 - 14 - SRP-350II 1-5-5 Be sure to note the correct direction that the paper comes off the roll. 1-5-6 Pull out a small amount of paper,

Rev. 1.04 - 15 - SRP-350II 1-6 Recommended Papers - TF50KS-E (Paper Thickness: 65μm): Nippon Paper Industries Co., Ltd. - PD 160R (Paper Thickness

Rev. 1.04 - 16 - SRP-350II 1-8 Using the Printer Control Panel 1-9 Connecting the computer You need an appropriate interface cable. 1-9-1 Pl

Rev. 1.04 - 17 - SRP-350II 1-10 Connecting the Power Supply ※ CAUTION When connecting or disconnecting the power supply from the printer, make sure

Rev. 1.04 - 18 - SRP-350II 2. Self Test The self-test checks whether the printer has any problems. If the printer does not function properly, contac

Rev. 1.04 - 19 - SRP-350II 3. Hexadecimal Dumping This feature allows experienced users to see exactly what data is coming to the printer. This can

Rev. 1.04 - 2 - SRP-350II Safety Precautions In using the present appliance, please keep the following safety regulations in order to pre

Rev. 1.04 - 20 - SRP-350II 4. Specification Printing method Thermal line printing Dot density 180 dpi (7dots/mm) Printing width 72 mm Paper width 79

Rev. 1.04 - 21 - SRP-350II 5. Appendix 5-1 Cleaning Printer Paper dust inside the printer may lower the print quality. In this case clean the print

Rev. 1.04 - 3 - SRP-350II CAUTION Violating following instructions can cause slight wound or damage the appliance. Do not use the pri

Rev. 1.04 - 4 - SRP-350II Warning - U.S.A This equipment has been tested and found to comply with the limits for a Class A digital device pursuan

Rev. 1.04 - 5 - SRP-350II Introduction The SRP-350II Roll Printer are designed for use with electronic instruments such as system ECR, POS, bankin

Rev. 1.04 - 6 - SRP-350II Table of Contents 1. Setting Up the Printer ...

Rev. 1.04 - 7 - SRP-350II 1. Setting Up the Printer 1-1 Unpacking Your printer box should include these items. If any items are damaged or missing,

Rev. 1.04 - 8 - SRP-350II 1-2 Connecting the Cables You can connect up the three cables to the printer. They all connect to the connector panel on t

Rev. 1.04 - 9 - SRP-350II 1-2-2 Parallel Interface (IEEE1284) Pin No. Source Compatibility Mode Nibble Mode 1 Host nStrobe HostClk 2 Host / Printe