◈ About This Guide
This installation guide contains only essential and simple information for installing the
product. Refer to the Users Guide in the CD that comes with the product for detailed
instructions. The CD contains the following data.
1. Manual: Users Guide (Control Command)
2. Drivers: Windows Drivers
3. Utilities: Logo Download Tool
BIXOLON makes continuous improvements for better quality and functions of its products,
therefore the specifications and contents of the manual are subject to change without prior
notice for this reason.
◈ Contents of the Package
SRP-150
Procuct Installation CDProcuct Installation CD
CD
Roll Paper
Power Cord
Installation Guide
Interface cable
(Serial/Parallel/USB)
◈ Cable Connection
1. Turn off the printer and ECR (host computer).
2. Connect the power cord to a power outlet.
3. Check the type of interface (serial, parallel, or USB) on the back of the printer and
connect the proper cable to the interface connector.
4. Connect the drawer kick-out cable to the drawer kick-out connector of the printer.
◈ Roll Paper Installation
1. Press the cover-open button and open the cover.
2. Insert a new roll paper in the right direction.
3. Pull the paper slightly and close the cover.
※ Note
Hold down the center of the cover when closing so
that the paper adheres to the roller.
◈ Control Panel
• Power (indicator lamp)
Green light will be on when the power is supplied to the printer.
• Error (indicator lamp)
Red light will be on in the event of errors such as no paper or open
cover.
◈ DIP Switch Setting
Changing DIP switch settings must be done while the printer is turned off. Changes made
while the power is on are not recognized.
• DIP switches: Serial
SW Function ON OFF Default
1-1 Auto Cutter Disable Enable OFF
1-2 Reserved -
1-3
Baud rate Refer to the following table OFF
1-4
Baud rate 1-3 1-4 Note
9600 bps OFF OFF Default value
19200 bps OFF ON
57600 bps ON OFF
115200 bps ON ON
• DIP switches: Parallel, USB
SW Function ON OFF Default
1-1 Auto Cutter Disable Enable OFF
1-2
Reserved -
1-3
1-4
◈ Self Diagnostic
1. Check that the paper is mounted correctly.
2. Turn on the power while depressing the Feed button. The self test will start.
3. The printer prints out the current status of the printer such as the ROM version and DIP
switch settings.
4. After printing the current status, printing stops after printing the following lines.
(Paper indicator lamp stays ON.)
Self-test printing.
Please press the FEED button
5. Press the Feed button to continue printing. The printer will print all types of characters that
can be printed.
6. Self test stops automatically and the printer cuts the paper after printing the followings
lines.
*** COMPLETED ***
7. The printer goes back to normal operating mode immediately after completing the self test.
※ Note
The status of the printer can be checked through the self test. Check the printing quality,
ROM version, and DIP switch setting through the self test.
◈ Product Specifications
Item Description
Printer
Printer type Thermal transfer (thermal) printing
Dot pitch 203 dpi (8dots/mm)
Printing width 48 mm
Number of characters
per line (default value)
32 (Font A) (12x24) / 42 (Font C) (9x24)
Printing speed *1) 19 lines/sec, 65 mm/sec
Receive buffer size 4Kbyte
SMPS input voltage 100 ~ 240 VAC
Frequency 50/60 Hz
SMPS output voltage 12 VDC
Temperature
0 ~ 45 ℃ (Operating)
-20 ~ 60 ℃ (Storage)
Humidity
10 ~ 80 % RH (Operating)
10 ~ 90 % RH (Storage)
; paper is not included
Auto cutter 1,000,000 cuts
Mechanism MCBF *2) 20,000,000 lines
Paper
Paper type Roll paper
Roll paper width 58 ± 0.5mm
Diameter of roll paper Maximum 80mm
Paper thickness 0.062~0.075 mm
※ Note
*1) Printing speed may be slower depending on the combination of data transfer speed and
commands.
*2) This value is based on the measurement at standard temperature, specified paper, and
printing level 2, and it can be changed depending on the temperature or printing level.
Printer Installation Guide
KN04-00037B (Rev.1.4)
Thermal Printer SRP-150
Power cord
Drawer
kick-out
cable
Interface cable
(Serial/Parallel/USB)
Drawer kick-out connector
Power connector
Interface connecto
(145 pagine)
(22 pagine)
(29 pagine)
(8 pagine)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale