BIXOLON STP-103DK Manuale Utente

POWERERRORFEEDON LINE KN04-00003ARev. 2.6 STP-103 THERMAL PRINTER www.samsungminiprinters.com USE

18 Chapter 7. Code Table The following pages show the character code tables. To find the character corresponding to a hexadecimal number, count acro

20 PC850 : Multilingual 21 PC860 : Portuguese

22 PC863 : Canadian – French 23 PC865 : Nordic

24 PC858: Euro 25 Space Page SP

26 27 Chapter 8. Functions The commands listed in the table below are available for control of the printer. Commands Command Classif

28 Command ClassificationCommand Name Execution Setting Standard Mode Esc c 5 Enable/disable panel FEED buttons 0 0 Esc d Print

30 CR [Name] Print and carriage return. [Format] ASCII HT Hex 0D Decimal 13 [Description]

32 ESC ! n [Name] Select print mode(s) [Format] ASCII ESC ! n Hex 1B 21 n Decima

34 ESC 2 [Name] Select 1/6-inch line spacing [Format] ASCII ESC 2 Hex 1B 32 Decimal 2

36 ESC R n [Name] Select an international character set [Format] ASCII ESC R n Hex 1B 52 n

2 Safety Precautions In using the present appliance, please keep the following safety regulations in order to prevent any hazard or material damage.

38 ESC c 5 n [Name] Enable/disable panel FEED buttons [Format] ASCII ESC c 5 n Hex 1B 63 3

40 GS ! n [Name] Select character size [Format] ASCII GS ! n Hex 1D 21 n Dec

42 n selects the printing position as follows: N Printing position 0,48 Not printed 1,49 Above bar code 2,50 Below bar code 3,51 Bo

44 ● When the LSB of m = 1: After waiting for the period specified by t, the LED indicator bli

46 GS f n [Name] Select font for Human Readable interpretation (HRI) characters. [Format] ASCII GS f n Hex

48 <Example> Printing GS k 72 7 67 111 100 101 13 57 51 [When CODE128 (m=73) is used :] ● Refer to Appendix J for t

50 GS v 0 xL xH yL yH dl…dk [Name] Print raster bit image [Format] ASCII GS v 0 m xL xH yL yH dl…dk

52 APPENDIX B : Specification Printing method Thermal line printing Dot density 200 x 200 Dpi (8 dot/mm) Printing width 48mm Paper width 58mm

54 2) Parallel Interface Connector Specification PRINTER HOST 1 /STROBE (I/O) 1 /STROBE (I/O) 2 DATA0 (I/O) 2 DATA0 (I/O) 3 DATA1 (I/O)

4 Warning – U.S This equipment has been tasted and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rule

6 Table of Contents Chapter 1. Unpacking 1-1. Checking the contents of the Printer 1-2. Locating the Printer 1-3. Printer Part names 1-4. Operati

8 1-3. Printer Part Names (1)(4) (3)(2)(5)(10)(11)Rear View Rear View STP-103S STP-103P(6) (7) (8)(9) Control Panel POWER ERROR FEED ON L

10 Chapter 2. Connecting the Cable 2-1. Connecting the AC adapter to your printer When the printer is used, use the optional AC adapter, NH36-24015

12 2-2. Connecting the printer to your Computer STP-103P You need an appropriate parallel interface cable to connect your computer to the printer&a

14 Chapter 4. Setting the DIP Switches CAUTION Turn off the printer while setting the DIP switch to prevent an electrical short, which can damage th

16 Chapter 5. Running the Self-test 1. Self-test printing 1) Starting the self test To start printing the self-test on a paper roll, hold down the